SPACEGASS Assignment ENGIN2203 Structural Analysis

{`
Course Code: ENGIN2203
Course Title: Structural Analysis
University: Federation University
Country: Australia
`}

Introduction

This exercise involves the use of Space Gass to investigate several issues of a structural nature. The objective of this exercise is to enhance your understanding of structural behaviour, as well as develop a basic competency in the use of an industry-standard structural analysis computer program. This assignment consists of two parts.

Please note that you need to upload 2 files in the Moodle submission link by the due date:

1) Complete report file for parts A and B (in Pdf format);

2) The SPACE GASS file for Part B (in .SG format).

Part A: 2-Span Continuous Beam

A 2-span continuous beam has the support arrangement, member sizes and loading shown below:

Each group will use an exclusive set of parameters for the input parameters. The method to generate input parameters is as follows: Count the number of letters of the first name of each group member and use the average of the two numbers as the value of X, then generate the parameters according to the table below (e.g. for Jack and Claire, X=5). Round up the obtained values to 1 decimal places.

a) Use the Slope-Deflection Method to analyse this beam and determine the joint moments MA, MB and MC. (Note: Please clearly identify the X value and the input you have used.) Note that the beams are bending about their strong axis (i.e. ‘x’ axis).
b) Using the joint moments determined in a), determine the vertical reactions VA, VB and VC. Thus draw the shear force diagram for this beam, determine from this the location of the maximum sagging bending moment in each span, and calculate the values of these maximum sagging bending moments. Finally, manually draw the full bending moment diagram for the beam.
c) Use Space Gass to analyse the beam to determine:

a.The full B.M.D. and compare the bending moments MA, MB and MC, and the maximum sagging B.M.’s with those determined in a) and b).

d) Perform several checks of the output results from Space Gass in order to validate the correctness of these results. Note that the results of the slope-deflection analysis are not to be regarded as one of these checks. Treat this part as if the slope-deflection analysis had not been done. All calculations must be shown.

Part b: Portal Frame Model

Introduction

This exercise continues on the second part of Assignment 1 to apply the wind loading on a typical steel portal frame building, using the SPACE GASS program. You need to use the group inputs and results of your calculations from Assignment 1. Please make sure you correct any mistakes undertaken in the previous assignment in order to get full marks for this part and mention a small summary of changes.

The diagram of the portal frame is attached. The portal frames are pinned-base, with the usual rigid connections at the eaves and the ridge. There is no haunch in the structure.

In a normal portal frame building design, a substantial number of wind loading scenarios would be considered. For this exercise, however, a very small subset of load cases, considering only the case of maximum uplift, will be investigated.

Requirements

For the portal framed structure described above and in the attached diagrams, and based on the dead load + wind load cases described below, the following is required:

A) Determine the following maximum design actions, derived from Load Cases 4 and 5, for the first internal portal frame in from the end of the building:
Maximum uplift on the footing (kN);

ii Maximum hogging moment at the ridge (kNm);

iii Maximum sagging moment at the rafter-column connection (kNm).

In addition to these answers, the following is to be included in the submission

All calculations involved in determining the loadings (from Assignment 1);

iiA fully dimensioned diagram of the model, showing member and node numbering and section sizes;

iii Fully detailed diagrams showing the loadings used for the three load cases LC1, LC2 and LC3; iv

The bending moment diagrams determined for the two load cases LC4 and LC5. Note that the various diagrams should be produced by SPACE GASS

B) Undertake a manual check of the column base vertical reactions for the two load cases LC4 and LC5. You should be able to get the same answer for the total nett vertical loading on the building as yielded by the sum of the two base reactions given by the SPACE GASS analysis. This provides a check that the loads have been correctly input into SPACE GASS.

Australia Universities

ACT

Australian Catholic University

Australian National University

Bond University

Central Queensland University

Charles Darwin University

Charles Sturt University

Curtin University of Technology

Deakin University

Edith Cowan University

Flinders University

Griffith University

Holmes Institute

James Cook University

La Trobe University

Macquarie University

Monash University

Murdoch University

Queensland University of Technology

RMIT University

Southern Cross University

Swinburne University of Technology

University of Adelaide

University of Ballarat

University of Canberra

University of Melbourne

University of Newcastle

University of New England

University of New South Wales

University of Notre Dame Australia

University of Queensland

University of South Australia

University of Southern Queensland

University of Sydney

University of Tasmania

University of Technology Sydney

University of the Sunshine Coast

University of Western Australia

University of Wollongong

Victoria University

Western Sydney University

Year 11 - 12 Certification Assignment

Australian Capital Territory Year 12 Certificate

HSC - Higher School Certificate

NTCE - Northern Territory Certificate of Education

QCE - Queensland Certificate of Education

SACE - South Australian Certificate of Education

TCE - Tasmanian Certificate of Education

VCE - Victorian Certificate of Education

WACE - Western Australia Certificate of Education

SPACEGASS Assignment ENGIN2203 Structural Analysis

Diploma Universities Assignments